Connectors

Use the following connectors with all sizes of fiber and cable, we carry many sizes and shapes to be used in projects, please choose the right connector for the right project i.e.: Above ground, Underground, Underwater, etc.

 

 

Use the FTC (Fiber Tight Connector) to hold fiber and cable to a wall or Lightbox. Fibers are held in place by a twist of a nut! .75mm fiber*. They come in 6 sizes:

FTC7 5/16 to 1/4" Hole 25 Fibers* . . $2.30 ea.

FTC9 7/16 to 3/8" Hole, 75 Fibers . . . $2.30 ea.

FTC11 3/8 to 1/2" Hole, 150 Fibers . . $2.70 ea.

FTC16 1/2 to 5/8" Hole, 300 Fibers . . $3.00 ea.

FTC21 5/8 to 3/4" Hole, 400 Fibers . . $6.50 ea.

FTC29 3/4 to 7/8" Hole, 550 Fibers . . $8.95 ea.  

FTC36 1 3/8" to 1" Hole, 550 Fibers . $29.00 ea.  

 

 

  P-Clips  & Float Clips

Our P-Clips are designed to hold the Fiber Cables from Sideglow to Endglow. 3 Sizes available:

3mm, 5mm, & 10mm

  .25c ea.  

or

Float Clips

Our F-Clips are designed to hold the Fiber Cables from Sideglow to Endglow. 1-1/2" away from walls

3 Sizes available:

3mm, 5mm, & 10mm

SIZE 14 IS NOT LONGER STOCKED

  .50c ea.  

 

 

 

 

 

Emitters & Detectors 

 

 The following devices are a family of low-cost, medium-frequency, short-distance fiber optic emitters and detectors. Each emitter and detector consists of a PVC housing, an internal active element such as an LED or Photo-detector and a cinch nut to hold the fiber in place. The PVC housing retains the active element and the cinch nut while optimizing coupling between the active element and the jacketed 1000 Ám plastic fiber.

These devises are simple: No special tools or training required. Only a sharp knife or razor blade is needed to terminate the plastic fiber, then a bit of polishing. When the fiber is inserted in the emitter or detector, tighten the cinch nut. Thereafter, the fiber can be removed simply by loosening the nut.

The IF-95T contains a Photo-logic detector with a totem-pole output and the 95OC is a similar detector with an open-collector option. Both versions contain an IC with a photodiode, linear amplifier, voltage regulator, and Schmitt trigger. The devices feature TTL/CMOS compatible logic level output which can drive up to 5 TTL over supply voltages ranging from 4.5 to 16 volts.

 

Click Here For Device Specs.

E96 & D92 (Pic above)

Ready to mount Emitters & Detectors, Infrareds and More!

E91A Infrared 940nm Emit ..$2.50

E91B 880nm Emit . . $2.65

E92 Blue Emitter . . . .$9.00

E93 Green Emitter . . . . . .$8.25

E96 Red LED Emitter. . . $3.75

E97 Bright Red . . . . . $4.50

E98 Red 50 Mbps . . $10.00

E99 Red 155 Mbps . . $25.00

D91 Photodiode . . . $2.90

D92 Phototransistor . . .$2.50

D93 Photo Darlington . . . $3.50

D96   5 Mbps Detector . . . $7.00

D97 Photo-Logic 50 Mbps. . $13.50

D98 Photo-Logic 155 Mbps . . $19.75

 

 

 

 

 

DNP (Dry-Non-Polished)

Connectors

The following are DNP connectors used with our Simplex and Duplex Plastic Cable ONLY.

Device Mount #43-1 Has sweet-spot hole for LED mounting. Use item #87-1 with this mount! $1.60 ea.

Single Position plug #87-1 slide simplex or fiber up to 2mm into hole and connect to mounts.

 $1.35

Retention Clip #46-1 use this to hold fibers in place, to be use with above item.

 .25c ea.

Duel Position Bulkhead #45-1 use this in conjunction with a Duel position plug.

$2.00 ea.

Duel Position Plug #88-1 use with our E2000 Duplex Cable fiber.

 $1.85 ea.

Single Position Plug #42-1 use with our Single position plug, connects two fibers together like a splice.

 $1.50 ea.

Splice Sleeve #51-1 slides over fiber to make splice .25c ea.

 

 

 

 

 

 

FC Style connector

$4.25 ea

This connector will hold 1mm fiber for perfect alignment connections.

We can get you any connector used with fiber optics available, see below list of connectors, then call or e-mail for pricing for part and special drilling.

 

 

 


Home

 Copyright ©  1998-2013 Fiber Optic Products, Inc.

10-2-13