LED Light Bars

LED LIGHT BARS

3" to 8" Bars

LED Light Bars 3"

& NEW 3.25"

Our NEW 3.25" LED bars come in all colors, they can interconnect to each other, you can mix colors also! Each bar has an LED spaced 3/4" apart. 4 Leds per bar.

All bars are for 12 VDC power. You need to order power supply based on total mA of bars !!!!

Bars Measure: 3.25 L X 5/8" W X 5/8" H

$3.00 to $2.75

Light Bar Tracking for 3" Bars

1.75 x 1" x 1/2"

Led Bar Jumper for 3" Bar, 5" Long

RGB FULL COLOR LED BARS

We now stock RGB full color LED bars, they fade from one color to the next. From Red thru the rainbow to blue and repeats. 3" Bars available only. The controller and bars are sold separately. You can light up to 10 3" LED bars with this controller. 12vdc power required.

Controller # 1 = Color change cycle: Adjustable From 2 seconds to 5 seconds. 7 color sets. and Fixed Color programs.
The controller # 1 measures 2 1/2"L x 1"W, and will handle up to 30 3" RGB Bars. But the traces on the RGB Bars can only handle 12 Bars Understand !!
RGB LED Bars Will NOT operate properly without the RGB Controller.
Luminous Intensity = 20,000 mcd
View angle = 60 degrees
Power Dissipation = .100mA Depends on # of bars running off controller.
Power Requirement = 12v DC
Manufacturer Rated Life = 80,000 Hours
More Power Connectors and Straight Connectors are sold separately.
You MUST order all parts together or the bars won't light !!

RGB 3" Bar

12 VDC @ 65mA Draw

$4.25 Ea.

OUR NEW

RGB Bar Controller #1

This unit can power up to 15 or our 3" RGB Bars or the 19" RGB-Flex Strips.

Slow color fade thru the rainbow. Push button once and Leds color will change to single color mode. Double Click button and now it will fade UP & Down. You can adjust fade speed by holding button down. Double click again and now you are in Strobe Mode. You can strobe in any color and adjust speed of strobe. Adjusting speed by watching the leds light from low to high in steps, the steps represent the speed mode for color wash. Its that simple !!

12 VDC input & Output. You need to order the 4 Pin Cable sold separately. To calculate the total number of bars you can light, divide the total output of your 12vdc transformer by its mA output:

I.E. 10 Strips @ .80 mA each = 800mA so you need a 12v 800mA Transformer !!

If using less bars order a smaller transformer.

Size: 1 2/1"L x 1" W

$24.50 ea.

4 Pin Controller Wire for # 1

.40 c ea.

Sound To Light RGB

Controller Unit

FOP and the crew has done it again to bring you the best in LED control lighting effects. Our NEW Sound-2-Light-RGB Unit.

The Unit comes with the following:

1 Port for our RGB bars, 3 Ports for Single color LEDs or LED bars.

Simple push button for selecting the color and effect you wish.

12vdc Power for Automotive, battery or Wall Power 12 800mA (Transformer include).

RCA Line-In Jack for connecting right to your Stereo.

Build in microphone.

Rainbow, Single Color, or Sound to Light Modes.

How It Works:

Select either Wall or Battery power, Select Line-In or Mic for incoming sound or music. Next Plug in your Leds or Led bars (Sold separately Click here). Push button to select from Sound to Light, Rainbow, or Single color mode. Unit has 3 Channels + 1 RGB out Channel. If you plug in a RGB bar then the out color will respond to the frequency set by the on board chip. You can also plug in 3 separate color led bars your choice of colors for responding to Low 60Hz to 150hZ - Mid 150-Hz to 3.5kHz - High 3.5KHz to 20KHz Frequencies. The out-put will dance to the music, push the button to adjust Brightness! Unit Measures: 2.75" Sq x 1" H

Note: Because most Music and Voice Frequencies are around the 1000Hz Range you may see the mid channel light most frequently.

Front Output Mic, Mode, RCS & Power LED Bars Lit Top Down View

S2LRGB-1 Unit

ONLY $69.95 Ea.

More Pages

Fiber Optics LED Lighting El Wire More Lighting & Misc. Items

Q & A: Most Asked Questions

Home

12-14-07